Now, let’s talk about more serious problems. You can attach a piece of duct tape from both sides to eliminate the possibility of it falling off. Tips and advices: Wipe the excess oil from the pin. All of the shooters from our squad were searching for the pin and we finally found it. Why did this happen? The answer is simple: There was too much oil on the pin. It looked funny to the spectators but not to Dmitry. The pin fell off my friend’s shotgun during the match. Why is this important? Because you may accidentally activate it while loading ammunition and you will have a round on the carrier while still trying to load ammo into the magazine tube. Here is a tip: Make sure the lower end of the button doesn’t protrude past the loading window. Matchsaver Location Comparison (Red by Manufacturer’s Instruction, Blue – My Version) I make sure the bolt is tightened regularly. However, the whole shooting season of 2016 has shown that it works well. Frankly, I was not sure if this was a reliable way by attaching the Matchsaver without a nut. Now I have a Matchsaver located as close to the ejection window as possible and there is no more problems loading a round into the chamber. That is why I have used the 3M duct tape and made that place more or less flat. The location of the Velcro, which is also used to attach a Matchsaver, has a pretty complicated form. Drilled a hole about two times smaller than the bolt in the forend and then tightened it in without the nut. I was able to solve it by the following way:
Benelli m2 cost install#
But the construction of the forend has not allowed me to install the nut on the bolt from the inside of the forend in order to attach a Matchsaver. I have located the Matchsaver close to the chamber. That is why I want to share nuances and tips with you right away.
And even long dry fire trainings could not guarantee 100% positive result. There is a small step between the receiver and forend that causes this to happen. But I have found that the shotshell hits the receiver sometimes when you try to load it into the chamber. You can put it on the forend, drill a hole and install it as designed by the manufacturer. It comes together with a template for the Benelli M2. You should use cotton fabric adhesive tape because the regular PVC adhesive plate will melt. Some people don’t like it, while some think that it is a common thing for the Benelli M2.Īttach several stripes of the cotton fabric adhesive tape on the inside of the forend to get rid of the play. The Forend of the Benelli M2 is loose from the beginning or it becomes loose with time. It is pretty easy to wipe the paint using a solvent. If you plan to paint the rear side of the vent rib with a paint color other than white, then you still need to paint it white for the background. My front sight is orange and my rear sight is white with a green line, for example. It is better to have different colors for the front and rear sights because it will result in better aiming. You should just remove it and buy a 3M adhesive strip and use it to attach the sight to the vent rib.Īdditionally, I used the duct tape to clamp the front sight and rib together for one day in order to apply pressure and allow the adhesive tape to stick better. The second problem which I had with the new sight is that the adhesive strip was dry and not adhesive at all. I decided to leave the factory sight to use it as a stop for the new EasyHit sight. Just use a regular cotton cloth and degrease the place of installation with something you usually use. It is hairy and it will leave particles on the vent rib. After this is done, you throw the cloth away immediately. The purpose of that 3M cloth is to degrease the vent rib before installing the sight. There was cloth which came in a sealed bag together with the front sight. Some of the issues are very interesting as well. Some of the issues are very typical and obvious but I will describe them anyway.
Instead, I will describe the important elements of fine tuning, the problems I’ve found and the ways to fix them. I am not going to describe upgrades, bells and whistles.
Benelli m2 cost how to#
This article is not for newbies and I won’t start describing how to prepare the Benelli M2 for practical shooting right out of the box.
I have used the Benelli M2 during 25 matches in Ukraine and abroad, so I have the knowledge to tell you about it.īut first, let me put a little disclaimer out there. I want to fix this and share my experiences of using this beauty throughout several shooting seasons. There are a lot of interesting articles in this blog, but there is not much information about the famous Benelli M2 shotgun. Thanks to my friend Igor Lytvynenko for this article.
0 kommentar(er)
